Before you start to use this device, please check if there’s anything
missing in the package, and contact your dealer of purchase to
claim for missing items:
Package Contents: 1x 7R152 Wifi Repeater
1x 1m Ethernet cable with RJ45 connector
1x Quick Installation Guide
Wireless-11N WallMounted Wifi Router 300M Quick Installation Guide Model： 7R152 LED indicators’ Status Description: WPS Button
Ethernet
Reset Button
WLAN LED
WPS LED
Ethernet LED
Power LED
Euro plug
Cautions: 1. Disconnect the device in thunderstorms in case of lightning damage.
2. Keep far from heat source and ensure ventilation.
3. Keep waterproof in the storage, transportation and operating environment.
Indicator Name
Power Status Indicator
Wireless Status Indicator
WPS Status Indicator
Ethernet Status Indicator
Green On Get Powered
Green slow blink Wireless Function Launched
Green fast blink
Not bright
WPS Function Launched
Not use or have
completed the connection
Green fast blink
Green fast blink
Green On
Data T
Ethernet Connected
Data T
Status Description
Reset: If need to reset the router
seconds, release until all other LED are off except Power LED.
Note: Please check whether the WiFi-Router accord with factory default settings
once you can’t download http://192.168.2.1. If you are still not sure what reasons,
you can reset the WiFi-Router
then try again.
Appearance Introduction 1 Computer Configuration 3 Configuration Mode 2 Connect To Wireless Network 1.1 Click “ Start→Control
Center→Change adapter ”
3.1.1 Operating Mode ”, you will see 3 modes:
Select “Bridge ” then click on “Save ”
3.2.5 Setup your info and click on “Next ”
3.2.6 Click “Finish ” wait for a few4 Reconnect to Router ”
to reconnect the router
3.1 Configure Bridge Mode
3.2.3 Wait a few seconds, then refresh the BrowserSetup Wizard ”,
then click on “Next ” to continue.
3.2.4 Y
L2TP / PPTP
Static IP: Select “Static IP ” and input the network’s IP address information,
then click “Next ”
3.2.1 Follow process 2.3 to 2.4.
3.2.2 Select “Router” then click on “Save ”.
3.2 Configure Router Mode
2.1 Pulg the Wi-Fi Router to a wall socket.
2.2 Click on the network icon( ) on the right
bottom of your desktop. Y
from the Wi-Fi RouterConnect ” and
wait for a few seconds.
2.4 The login screen below will appear
Enter the “Username ” and “Password ”
then click “Login ” to login. The default
Username is “admin ” and Password is
“admin ”.
2.3 Open web browser and type http://192.168.2.1 in the browser’s address
box. This number is the default IP address for this devices.
1.2 Double click “Internet Protocol V”
1.3 T
2~252), subnet mask of 255.255.255.0, Click “OK ”. Back to the last
interface and click “OK ”
01 Wir 02 Wir 03 Wir
05 Wir04 Wir 06 Wir 07 Wir
300Mbps Wireless R
FW RVE: 7R152_V1.0
300Mbps Wireless R
FW RVE: 7R152_V1.0
300Mbps Wireless R
FW RVE: 7R152_V1.0
300Mbps Wireless R
FW RVE: 7R152_V1.0 300Mbps Wireless Router FW RVE: 7R152_V1.0 300Mbps Wireless Router FW RVE: 7R152_V1.0 300Mbps Wireless Router FW RVE: 7R152_V1.0 3.2.7 Select “DHCP ” and click “Next ”, then follow process 3.2.5 to 3.2.6
3.2.8 Select “PPPoE ” and fill your Username and Password provided by
network operator
Follow process 3.2.5 to 3.2.6 after click “Next ”.
300Mbps Wireless Router FW RVE: 7R152_V1.0 
Got a question?
Do you have a question about the 7inova and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other 7inova owners to provide you with a good answer.
Number of questions: 0