A6. After logging in and click “Setup Wizard”, you will see the web page below:
Select “Wireless Repeater Mode (Station)” and click on ‘Next’ to continue.
Wireless-N Wifi Repeater
04
Wireless-N Wifi Repeater
03
Wireless-N Wifi Repeater
02
You can configure the Wi-Fi Repeater by connecting it with your computer/laptop with enclosed RJ45 cable or wirelessly. We recommend you to do it with wire.A2. Click the “Start” button (it should be located at the lower-left corner of your screen), then click “Control Panel”. Click “View Network Status and Tasks”, and then click “Manage Network Connections”. Right-click “Local Area Network”, then select “Properties”. When the “Local Area Connection Properties” window appears, select “Internet Protocol Version 4 (TCP/IPv4)” and then click “Properties”.
A1. Plug the Wi-Fi Repeater to a
wall socket. Connect your computer
/ laptop with the Wi-Fi Repeater with
enclosed RJ45 Cable.
A3. Setting IP address manually: Type IP address is 192.168.10.x (x is from 2 to 254), and Subnet mask is 255.255.255.0. Type the Router’s LAN IP address (the default IP is 192.168.10.1) into the Default gateway field.
How to configure the Wi-Fi RepeaterA. Configure the Wi-Fi Repeater with RJ45 Cable
For a typical wireless setup at home (as shown below), please do the
following:
You will need WiFi
AP/Router Internet access
You will need broadband
Router Internet access
Connect the WiFi-Repeater
to your Router/Switch with
RJ-45 Cable
Setting up a Wireless Infrastructure Network
Wireless Repeater ModeGetting StartedWireless AP ModeWireless-N Wifi Repeater
01
The WiFi Repeater is a combined wired/wireless network connection device
designed specifically for small business, office, and home office networking
requirements. It allows a wireless network to be expanded using multiple access
points without the need for a wired backbone to link them. It also works well with
other 11b/g and 11n protocol wireless products.
NOTE: If you need to reset the Wi-Fi Repeater, you need press and hold the
reset button inside the tiny hole for 10 seconds.
Before you starting to use this router, please check if there's anything missing in
the package, and contact your dealer of purchase to claim for missing items:
·1 x Wireless-N Repeater
·1 x RJ-45 Networking Cable
·1 x Quick installation Guide
Introduction：Package ContentsA7. Click on ‘Repeater – OneKey Setting’ buttonA8. Wait a few seconds and you will see the site below and please click on ‘Wireless Network Selection’ button.Wireless-N Wifi Repeater
05
A9. Click on ‘Refresh List’ button. Select the Wireless SSID and click ‘Next’ to continue.
A10.When you see the site below, please do not change any setting but only
insert the password of your network.
Click on ‘Apply and Reboot’ button.
Wireless-N Wifi Repeater
06
A11. Click ‘OK’ to confirm. The Repeater will restart.
A12. Wait a few seconds and you will see the status site like below. It means your Wi-Fi Repeater is ready for use.
The Wi-Fi Repeater1 WLAN key is same with your router.
If you do not see the site like above, you need to re-configure it again.
NOTE: If you need to reset the Wi-Fi Repeater, you need press the reset button
inside the tiny hole for 10 seconds.
Wireless-N Wifi Repeater
07
Wireless-N
展开尺寸:360 x 240 m m
成品尺寸:120 x 90 m m
View the manual for the Sanoxy WAP-300 here, for free. This user manual comes under the category wifi repeaters and has been rated by 1 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Sanoxy WAP-300? Ask your question here
Do you have a question about the Sanoxy and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Sanoxy owners to provide you with a good answer.
Linux, Linux Kernel 3.0.8, Linux 2.6.18-2.6.38, Microsoft Windows, Windows ME, Windows 98SE, Windows Vista 32/64 bit, Windows XP 32/64 bit, Windows 2000 32/64 bit, Mac OS, Mac OS 10.8, Mac OS 10.7, Mac OS 10.6, Mac OS 10.5, Mac OS 10.4
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Sanoxy WAP-300 below.
What is the weight of the Sanoxy WAP-300?
The Sanoxy WAP-300 has a weight of 454 g.
What is the difference between a router and a modem?
A modem provides the internet connection via the internet provider. A router then distributes the Internet signal to the devices connected to the router.
What does the download speed on the internet depend on?
The download speed on the internet depends on the type of connection you have. If you have a 25 Mb/s connection this means that theoretically you should be able to download 25 MB per second.
Is WIFI radiation harmful?
WIFI is a radio frequency signal in the form of non-ionising radiation. This radiation cannot damage cells and tissues and is therefore not harmful to human health.
What certifications does the Sanoxy WAP-300 have?
The Sanoxy WAP-300 has the following certifications: Wi-Fi, RoHS, CE Mark (Europe), FCC (USA).
Is the manual of the Sanoxy WAP-300 available in English?
Yes, the manual of the Sanoxy WAP-300 is available in English .
Got a question?
Do you have a question about the Sanoxy and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Sanoxy owners to provide you with a good answer.
Number of questions: 0