RC420+TR310 outdoor remote control set OWNERS MANUAL Congratulations on your
purchase of a UPM outdoor
remote control set. Please
take the time to read and
understand this manual so
you can begin to enjoy the
convenience this product
has to offer.
FEATURES ! 433 MHz RF technology ! Control up to 2 remote receivers
! Heavy duty loading up to 1800W / 15A resistive
! Drip-proof cover design ! Transmission range of up to 30 meters in open
area
GETTING STARTED battery installation TROUBLESHOOTING 1
2
1
2
remove the battery cover from
the back of the transmitter
place two button cell batteries
between terminals observing
proper polarity, then replace cover
Transmitter stops turning receiver
on and off.
Use the LEARN function to
reprogram the receiver
or
Check the battery.
problem solution TECHNICAL SPECIFICATIONS Ratings: 120V AC, 15A
Max Load: 1800W resistive; 600W tungsten
Transmission Range: up to 30 meters in open area
Transmission Frequency: 433.92 MHz
Receiver
Transmitter
Batteries are not required in the RC420
receiver. T
included for the TR310 transmitter.
3
the green LED will light up
with any key press once the
battery is installed correctly
3
button descriptions ON/OFF
LEARN - used when
programming receiver
channel
LED indicator
CH 1 - ON
CH 1 - OFF
Learn
On/Off
Cord
120V 15A Plug
LED
Indicator
Learn Key
On/Off Key
Learn
On/Off
LEARN FUNCTION 2
Press LEARN on receiver while
simultaneously pressing the desired
channel button on the transmitter
1
Plug receiver into wall socket
4
If LEARN is completed successfully,
the LED on the receiver should light
up when ON is pressed
2
The ON/OFF button on the receiver
also turns power on and off
1
Power On/Off by using the ON/OFF
keys on the transmitter
ON/OFF FUNCTION 2
3
4
1
2
Learn
On/Off
Learn
On/Off
This device complies with Part 15 of the FCC Rules of Operation and is
subjected to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received,
including interference that may cause undesired operation.
FCC COMPLIANCE 3
Repeat and for an additional
receiver (available at your local
retailer)
1
2
INSTRUCTION TO THE USER This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions , may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
! Reorient or relocate the receiving antenna. ! Increase the separation between the equipment and receiver. ! Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
! Consult the dealer or an experienced radio/TV technician for help. In order to maintain compliance with FCC regulations, shielded cables must
be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception.
The user is cautioned that changes and modifications made to the equipment
without the approval of manufacturer could void the user’s authority to
operate this equipment.
CH 2 - ON
CH 2 - OFF
MOUNTING BRACKET WARNING: To avoid shock hazard, timer must be installed vertically and at least 3 ft.
above ground level.
For safe and optimal performance, use the supplied mounting bracket
timer vertically and flush against the wall. Y
accessories (i.e. power drill, bits, screws, and/or screwdriver) for proper installation.
http://waterheatertimer.org/UPM-timers-and-manuals.html
Got a question?
Do you have a question about the UPM and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other UPM owners to provide you with a good answer.
Number of questions: 0